1900 MHz Yagi Antenna (50 Ohm, SureCall SC-230-1900)

2G and 3G 1900 MHz Single Band Yagi Antenna. It works with 50 Ohm systems. It is an outdoor directional antenna. Part number SureCall SC-230-1900/ Cellphone-Mate CM-230-1900. It provides antenna reception Gain of 14 dB on 1850 MHz to 1990 MHz frequency band. It has a Type N-Female connector.

Sure-Call SC2301900/ Cellphone-Mate CM2301900 purchase includes mounting kit as well. The Yagi is a directional antenna that is designed to be used in areas of weak cellular signal. It is aimed directly at a cellular tower to provide the maximum connectivity. It is weather resistant. It is easy to install. Once up and running, the Yagi gives you faster data speed, and improved cellular signal.

With an impedance of 50 Ohm, the antenna is a high gain type, best for outdoors. Point it towards the cellular tower that is not only unobstructed but also the nearest. Do point it to the cell tower that belongs to the Carrier whose signals need to be boosted. Alternate part numbers: SureCall SC230-1900/ Cellphone-Mate CM230-1900. UPC: 896831002210.

From the manufacturer:

Summary:

• Outside use.
• Directional.
• 14 dB Gain.
• 2G, 3G.
• Single Band @ 1900 Mhz.
• Easy to install.

Overview:

These directional Yagi antennas are the best performing antennas on the market today. They are high gain outdoor antennas that should be pointed toward the nearest cellular tower. This antenna is designed to cover 2G and 3G systems for PCS frequency range. This single band antenna is designed to work with similar one band in-building amplifiers for PCS band that spans frequency 1850 MHz to 1990 MHz. This low profile antenna is an external directional Yagi antenna commonly used with our 1900 MHz in-building amplifiers. It works with all networks operating at 1900 MHz frequency.

SureCall SC-230-1900 Specifications.

SureCall SC-230-1900 Set Up Instructions.

CellphoneMate CM230-1900 MHz Yagi Antenna is a directional antenna.  Directional antennas need to be pointed toward the nearest cellular tower for the best results. CellPhone Mate CM230-1900MHz Yagi Antenna includes mounting equipment to attach to a pole .5 inch to 1.5 inch in diameter (pole not included). 

1. Place a U-bolt around the pole and through the two holes at the top and of the antenna plate.
   
   
2. Place a flat washer, a lock washer and a hex nut on each of the bolt ends.
   
   
3. Using an adjustable wrench or 1/2" wrench, tighten the nuts.
   
   
4. Place the second U-bolt around the pole and through the two holes at the bottom of the shelter.
   
   
5. Put a flat washer, a lock washer, and a hex nut on each bolt end, and tighten the hex nuts so that the Yagi remains in place, but can still be adjusted.
   
   
6. Rotate the Yagi so that is points to the desired station/repeater/receiver.
   
   
7. Tighten the hex nuts so that the Yagi is firmly attached.
   
   
8. Place the omni antenna a distance above the Yagi antenna, providing space between the mounted antennas. Ideally, omni antenna should be mounted flush with the very top of the pole, so that the pole does not interfere with the antenna’s communication.
   
   
9. While holding the omni antenna against the pole, place a U-bolt around the pole and through the two holes at the top and of the antenna plate.
   
   
10. Place a flat washer, a lock washer and a hex nut on each of the bolt ends.

   11. Using an adjustable wrench or 1/2" wrench, tighten the nuts.

   12. Place the second U-bolt around the pole and through the two holes at the bottom of the shelter.