DC 12V-36V 500W PWM Brushless Motor Controller with Hall Motor Voltage Speed Regulation Balanced Car Driver Control

DC 12V-36V 500W PWM Brushless Motor Controller with Hall Motor Voltage Speed Regulation Balanced Car Driver Control

Name: DC 12V-36V 500W PWM Brushless Motor Controller with Hall Motor Voltage Speed Regulation Balanced Car Driver Control
Brand: Elecbee
SKU: 1758372
Price: 16.99 USD
Availability: InStock
Rating: 137 / 29 (29 reviews)

$16.99

SKU: 1758372

Copy to clipboard

85 Sales

29 reviews

In Stock Availability

Bulk Purchase, Auto Savings:

$16.14

10-19 PCS

$15.29

20-99 PCS

$13.59

100+ PCS

Deliver to United States

Flat Shipping Rate $10.00

Item Type

- +

Contact Sales

DC 12V-36V 500W PWM Brushless Motor Controller with Hall Motor Voltage Speed Regulation Balanced Car Driver Control

1758372

Your Name*
Your Email*
Topic*
Qty
Message	Message
SUBMIT

Pay with Ease

Trusted Delivery

Mobile

Description

Description:

Operating voltage: DC 12V-36V

Operating Current: <=15A

Driver Power: <=500W

Speed Voltage: 0.1V-5V

Operating Temperature:-40-85C

Humidity: 90%RH

Stall protection:Yes

Enable Control: Yes

Over-current protection: Yes

Steering control: Yes

Speed control signal: Yes

Size: 63*42*17mm(L*W*H); Probe size 3mm,length: fixing hole center distance 57mm; width:fixed hole center distance 36.5mm

Power terminal Out:

VCC(positive power supply)

GND(negative one)

MC(motor phases W)

MB(motor phases V)

MA(motor phase U)

Set for the control side:

GND control terminal ground

VR the governor end 0-5V(corresponding to 10% of motor speed -100%)

ZF reversing control(connected to 5V or ground can charge the motor rotation direction)

M tachometer pulse output(depending on the number of motor poles corresponding to the number of pulse per revolution of the output number)

EL enable control terminal(connected to 5V ot ground running then 5V, grounding the motor stops)

5V 5V control terminal

HALL for the hall terminals:

5V, Hall power positive

Ha, Hall signal

Hb, Hall signal

Hc, Hall Signal

GND, Hall negative

Wiring:

Control terminal for SET:

1. The motor speed control wiring methods: available potentiometer system speed can also be connected to the MCU control, when the potentiometer control wiring, the potentiometer middle pin is connected to VR speed port, potentiometer connected to both ends of 5V and GND terminal voltage more high speed faster

2. Motor steering control wiring methods: you can switch control can also be connected to the MCU control, to GND in one direction, then in one direction 5V

3. Pulse speed signal: high and low output . IC can not understand the information with the customer request

Hall signal inputs for hall:

Wiring diagram is shown, one corresponding to the HA, HB,HC and on the motor, 5V power supply connected to the motor hal signals positive, GND power supply negative signal to the motor hall

Note: Due to different motor manufacturers to make the hall of hall line order does not necessarily follow the line on the board to match the array, need to be adjusted, please pay attention! If the line array wrong, does not boot properly, current, or start other phenomena not open, forced to use the drive plate will burn!!!

Motor driver board 12-36V DC power input ,VCC positive power supply,GND power supply is negative

Electrical wiring methods: Brushless DC motor for the three lines, corresponding MA/U,MB/V,MC/W

Tips: If you use less than 60W, without additional heat sink , be sure to add more than 60W heatsink fins drive efficiency without lowering the temperature is too high will shine into permanent damage! The size of the heat sink may be a bad environment based work(recommended cooling surface area greater than 200 square centimeters)!When installing the heat sink ,must pay attention to the back of the module 6 MOS pipe insulation, no insulation, it will be adhered to drive plate permanently damaged! Proposes to add insulation films, both sides of the insulating sheet plus thermal grease!

Package includes:

1 x Controller

DC-12V-36V-500W-PWM-Brushless-Motor-Controller-with-Hall-Motor-Voltage-Speed-Regulation-Balanced-Car-1758372

Reviews (29)
comment

Q & A

: Where is the origin of Elecbee products? Are they certificated?

2023-03-03

Answer:

Elecbee has long-term cooperation agreements with the OEM factories in China. So that we are able to reduce the intermediate channel cost, and help you save money. Our products are all made strictly according to the relative global standard, to ensure the products have good compatibility and excellent quality.

2023-03-03

: What forms of payment do you accept?

2023-03-03

Answer:

Our main payment methods include Paypal, Credit Cards, Debit Cards, Bank Transfer, and more to discover. Please choose the payment methods in your favor.

2023-03-03

: When will you arrange shipment?

2023-03-03

Answer:

After confirming receipt of your payment. We will arrange the delivery as soon as possible and upload the courier number to the website for you to track.

2023-03-03

: How to exchange or return?

2023-03-03

Answer:

1. You can apply to return within 30 days after receipt of the goods. Please make sure the outside package is intact, and the product is in its original condition. We will arrange your refund according to the relevant provisions once the package is received.

2. Return process: You Apply for a Return - Approve the Return - Arrange a Return - Receive the Products and make Inspection - We arrange a Refund;

3. We will bear the freight charges for returns caused by us, for instance, the quality problem. As to returns caused by the buyer, the buyer should be responsible for the shipping fee.

2023-03-03