SpeedyBee F405 V3 Flight Controller - FPV
- Description
The SpeedyBee F405 V3 Flight Controller - 30x30 features Bluetooth pairing! It's also built with a 4-level LED battery indicator in case you don't have your LiPo checker handy. The F405 V3 FC also features a built-in barometer, m1-m8 ESC signal, and 4x UARTS.
Dedicated DJI Air Unit connector for a quick digital build
Power your GPS with a USB cable - no battery needed.
4 x UARTs for your receiver + VTX + camera + GPS.
SD Card slot can support up to 4GB Blackbox data*
22mm cutouts for FPV camera in your tight build
9V 2A + 5V 2A individual BECs
4-level LED battery indicator
m1-m8 ESC signal
Built-in barometer
Bluetooth pairing
BOOT Button: Supported.
[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the BOOT button can be used to control the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
Blackbox MicroSD Card Slot: *Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High Capacity (SDHC), so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also, the card MUST be formatted with the FAT16 or FAT32 (recommended) filesystems. So, you could use any SD card less than 32GB, but Betaflight can only recognize 4GB maximum. We suggest you use this 3rd party formatting tool and choose 'Overwrite format' and then format your card. Also, check out here for the recommended SD cards or buy the tested cards from our store.
5V Output: 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 2A.
Traditional Betaflight LED Pad: Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
9V Output: 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 2A.
4.5V Output: Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
Power Input: 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)
Current Sensor Input: Supported. For SpeedyBee BLS 50A ESC, please set scale = 386 and Offset = 0.
3.3V Output: Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
DJI Air Unit Connection Way: Two ways supported: 6-pin connector or direct soldering.
I2C: Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
Supported Flight Controller Firmware: BetaFlight(Default), EMUFlight, INAV
UART: 5 sets(UART1, UART2, UART3, UART4(For ESC Telemetry), UART6)
BLE Bluetooth: Supported. Used for Flight Controller configuration
SmartPort: Use any TX pad of UART for the SmartPort feature.
ESC Signal: M1 - M4 on bottom side and M5-M8 on front side.
BetaFlight Camera Control Pad: Yes(CC pad on the front side)
RSSI Input: Supported. Named as RS on the front side.
Mounting: 30.5 x 30.5mm( 4mm hole diameter)
Buzzer: BZ+ and BZ- pad used for 5V Buzzer
Firmware: Target Name SPEEDYBEEF405V3
Dimension: 41.6(L) x 39.4(W) x 7.8(H)mm
ESC: Telemetry UART R4(UART4)
OSD Chip: AT7456E chip
USB Port Type: Type-C
IMU(Gyro): BMI270
Barometer: Built-in
MCU: STM32F405
Weight: 9.6g
Package Include
1x SpeedyBee F405 V3 Flight Controller - 30x30
5x M3x8mm Silicone Grommets(for FC)
1x SH 1.0mm 30mm-length 8pin cable(for FC-ESC connection)
1x DJI 6pin cable(80mm)
- Reviews (20)
-
comment
- Q & A
-
: Where is the origin of Elecbee products? Are they certificated?2023-03-03
-
Answer:
Elecbee has long-term cooperation agreements with the OEM factories in China. So that we are able to reduce the intermediate channel cost, and help you save money. Our products are all made strictly according to the relative global standard, to ensure the products have good compatibility and excellent quality.
2023-03-03
-
: What forms of payment do you accept?2023-03-03
-
Answer:
Our main payment methods include Paypal, Credit Cards, Debit Cards, Bank Transfer, and more to discover. Please choose the payment methods in your favor.
2023-03-03
-
: When will you arrange shipment?2023-03-03
-
Answer:
After confirming receipt of your payment. We will arrange the delivery as soon as possible and upload the courier number to the website for you to track.
2023-03-03
-
: How to exchange or return?2023-03-03
-
Answer:
1. You can apply to return within 30 days after receipt of the goods. Please make sure the outside package is intact, and the product is in its original condition. We will arrange your refund according to the relevant provisions once the package is received.
2. Return process: You Apply for a Return - Approve the Return - Arrange a Return - Receive the Products and make Inspection - We arrange a Refund;
3. We will bear the freight charges for returns caused by us, for instance, the quality problem. As to returns caused by the buyer, the buyer should be responsible for the shipping fee.
2023-03-03
Related Products
EB-900-0148
